Antenna-coupled diode solar cells, also called rectenna solar cells, work on an entirely different principle, much like a crystal radio receiver but for light. Incoming solar radiation (electromagnetic waves) is received by sub-micron-size antennas, which convert it to ultra-high-frequency alternating current (AC). This current passes through a nanometer-scale, ultra-high-frequency diode, which converts the AC to direct current (DC) and provides usable power (see Figure 1). A solar cell would incorporate a large array of millions of these elements in tandem deposited onto a glass or plastic substrate. Fabrication costs can be low, with devices processed cheaply in a roll-to-roll process.1
In principle, the conversion efficiency for rectenna solar cells can be very high, limited to 93% by the entropy of the photon gas,2 but other constraints limit the efficiency to well below this number. The demands placed on the diode are extreme. First, it must operate efficiently at extremely high frequencies—close to a petahertz (1015Hz) for visible light—orders of magnitude higher than the fastest electronics. Second, it must couple electrical power efficiently from the antenna. To do so, the impedance (a measure of the ratio of the voltage magnitude and phase to that of the current in an electronic element) of the diode must match the low impedance of the antenna. Unfortunately, the two requirements conflict with each other. An additional challenge for rectenna solar cells is power loss in the antenna, because, at petahertz frequencies, metals become very resistive. One possible solution is to use dielectric antennas.3
A particular implementation for rectenna solar cells was patented in 1984.4 In a project led by ITN Energy Systems,5 our group developed metal/insulator/metal (MIM) diodes for rectenna solar cells.6 MIM diodes make use of femtosecond-fast transport of electrons tunneling through a nanometer-thick insulating region. By adding a second insulating layer, we can enhance the device nonlinearity.6, 7 An example of an MIM diode coupled to a bow-tie antenna for terahertz operation is shown in Figure 2. Extending the response to efficient power conversion at visible (petahertz) frequencies is problematic. To be fast, the diode capacitance must be small. For a device such as an MIM diode, which is sandwiched between two electrodes, the device area must be small, well below 1μm2. However, for a diode to have a low resistance, it must pass a large current at low voltage, which corresponds to a large area. The conflicting area requirements are fundamental and, so far, have precluded the use of MIM diodes for direct solar conversion.8
A completely different approach is a device we call a geometric diode. In a conductive material, charge carriers move unimpeded for a mean-free path length (MFPL) until they collide with a defect (a thermal vibration or a surface). A geometric diode consists of a thin film with an asymmetric structure no greater in size than the MFPL—see Figure 3(a)—in which charge carriers move more easily to the left than to the right. This planar structure avoids the capacitance/resistance tradeoff because it is not a sandwich structure. Made out of a conductive material, it can have both low resistance and ultra-low capacitance. The challenging part is that the MFPL tends to be tiny, requiring ultra-fine lithography to form the device. For metals, the MFPL is only a few nanometers, but for graphene films it can be hundreds of nanometers or more. For that reason, we make our geometric diodes from graphene: see Figure 3(b).
Developing an efficient rectenna solar-cell technology is a major undertaking. A key challenge, providing a diode that can convert the petahertz frequencies of visible light to DC and couple efficiently to antennas, cannot be met by conventional technologies. We presented a new device that may provide the solution, the geometric diode. Specifically, we demonstrated a geometric diode that works in converting IR light (corresponding to 28THz) to DC, but much development remains. The materials and the structure of geometric diodes will have to be improved to form a practical rectenna solar-cell diode technology. Even the basic theory of operation needs more work, because at petahertz frequencies it must be analyzed using quantum mechanics, with very different characteristics from the classical AC-to-DC converters that we are used to. These aspects represent the focus of our future work.
Garret Moddel, a professor since 1985, is developing new energy conversion technologies. Recently he served as president & CEO of Phiar Corporation, a company developing metal/insulator/metal rectenna detectors. He earned a BSEE degree from Stanford and MS and PhD degrees in applied physics from Harvard.
Zixu Zhu is a PhD student working on geometric diodes. He received his bachelor’s degree in electrical engineering from Brigham Young University in 2008.
Silicon Materials & Devices Group National Renewal Energy Laboratory
Sachit Grover is a post-doctoral researcher working on thin film silicon solar cells. He received his MS and PhD degrees in 2009 and 2011, respectively, from the University of Colorado, and a Bachelor of Technology in electrical engineering from the Indian Institute of Technology in 2006.