As the world builds out ever larger installations of wind and solar power systems, the need is growing for economical, large-scale backup systems to provide power when the Sun is down and the air is calm. Today’s lithium-ion batteries are still too expensive for most such applications, and other options such as pumped hydro require specific topography that’s not always available.
Now, researchers at Massachusetts Institute of Technology (MIT) and elsewhere have developed a new kind of battery, made entirely from abundant and inexpensive materials, that could help to fill that gap. The new battery architecture, which uses aluminum and sulfur as its two electrode materials, with a molten salt electrolyte in between, is reported in a paper in Nature by MIT professor Donald Sadoway, along with 15 others at MIT and institutions in China, Canada, Kentucky and Tennessee. “I wanted to invent something that was better, much better, than lithium-ion batteries for small-scale stationary storage, and ultimately for automotive [uses],” explains Sadoway. In addition to being expensive, lithium-ion batteries contain a flammable electrolyte, making them less than ideal for transportation. So, Sadoway started studying the periodic table, looking for cheap, Earth-abundant metals that might be able to substitute for lithium. Iron is a commercially dominant metal, but it doesn’t have the right electrochemical properties for an efficient battery. The second-most-abundant metal in the marketplace – and actually the most abundant metal on Earth – is aluminum. “So, I said, well, let’s just make that a bookend,” says Sadoway. “It’s gonna be aluminum.” Then came deciding what to pair the aluminum with for the other electrode, and what kind of electrolyte to put in between to carry ions back and forth during charging and discharging. The cheapest of all the non-metals is sulfur, so that became the second electrode material. As for the electrolyte, “we were not going to use the volatile, flammable organic liquids” that have sometimes led to dangerous fires in cars and other applications of lithium-ion batteries. The researchers tried some polymers but ended up looking at a variety of molten salts that have relatively low melting points – close to the boiling point of water, compared with nearly 1000°F for many salts. “Once you get down to near body temperature, it becomes practical” to make batteries that don’t require special insulation and anticorrosion measures, says Sadoway. The three ingredients they ended up with are cheap and readily available – aluminum, no different from the foil at the supermarket; sulfur, which is often a waste product from processes such as petroleum refining; and widely available salts. “The ingredients are cheap, and the thing is safe – it cannot burn.” In their experiments, the researchers showed that the battery cells could endure hundreds of cycles at exceptionally high charging rates, with a projected cost per cell that is about one-sixth of comparable lithium-ion cells. They also showed that the charging rate was highly dependent on the working temperature: the battery cells charged 25 times faster at 110°C (230°F) than 25°C (77°F). Surprisingly, the molten salt the team chose as an electrolyte simply because of its low melting point turned out to have a fortuitous advantage. One of the biggest problems in battery reliability is the formation of dendrites, which are narrow spikes of metal that build up on one electrode and eventually grow across to contact the other electrode, causing a short-circuit and hampering efficiency. But this particular salt, it happens, is very good at preventing that malfunction. The chloro-aluminate salt they chose “essentially retired these runaway dendrites, while also allowing for very rapid charging,” Sadoway says. “We did experiments at very high charging rates, charging in less than a minute, and we never lost cells due to dendrite shorting.” “It’s funny,” he says, because the whole focus was on finding a salt with the lowest melting point, but the catenated chloro-aluminates they ended up with turned out to be resistant to the shorting problem. “If we had started off with trying to prevent dendritic shorting, I’m not sure I would’ve known how to pursue that,” Sadoway says. “I guess it was serendipity for us.” What’s more, the battery requires no external heat source to maintain its operating temperature. The heat is naturally produced electrochemically by the charging and discharging of the battery. “As you charge, you generate heat, and that keeps the salt from freezing,” Sadoway says. “And then, when you discharge, it also generates heat.” In a typical installation used for load-leveling at a solar-generation facility, for example, “you’d store electricity when the Sun is shining, and then you’d draw electricity after dark, and you’d do this every day. And that charge-idle-discharge-idle is enough to generate enough heat to keep the thing at temperature.” According to Sadoway, this new battery formulation would be ideal for installations of about the size needed to power a single home or a small-to-medium business, producing on the order of a few tens of kilowatt-hours of storage capacity. For larger installations, up to utility scale of tens to hundreds of megawatt hours, other technologies might be more effective. These include the liquid-metal batteries that Sadoway and his students developed several years ago and that formed the basis for a spinoff company called Ambri, which hopes to deliver its first products within the next year. For that invention, Sadoway was recently awarded this year’s European Inventor Award. The smaller scale of the aluminum-sulfur batteries would also make them practical for uses such as electric vehicle charging stations, Sadoway says. He points out that when electric vehicles become common enough on the roads that several cars want to charge up at once, as happens today with gasoline fuel pumps, “if you try to do that with batteries and you want rapid charging, the amperages are just so high that we don’t have that amount of amperage in the line that feeds the facility.” So having a battery system such as this to store power and then release it quickly when needed could eliminate the need for installing expensive new power lines to serve these chargers. The new technology is already the basis for a new spinoff company called Avanti, which has licensed the patents to the system. It was co-founded by Sadoway and Luis Ortiz, who was also a co-founder of Ambri. “The first order of business for the company is to demonstrate that it works at scale,” Sadoway says, and then subject the battery to a series of stress tests, including running through hundreds of charging cycles. Would a battery based on sulfur run the risk of producing the foul odors associated with some forms of sulfur? Not a chance, Sadoway says. “The rotten-egg smell is in the gas, hydrogen sulfide. This is elemental sulfur, and it’s going to be enclosed inside the cells.” This story is adapted from material from MIT, with editorial changes made by Materials Today. The views expressed in this article do not necessarily represent those of Elsevier. Link to original source.