In the puzzle of climate change, Earth’s oceans are an immense and crucial piece. The oceans act as an enormous reservoir of both heat and carbon dioxide, the most abundant greenhouse gas. But gathering accurate and sufficient data about the oceans to feed climate and weather models has been a huge technical challenge.
Over the years, though, a basic picture of ocean heating patterns has emerged. The sun’s infrared, visible-light, and ultraviolet radiation warms the oceans, with the heat absorbed particularly in Earth’s lower latitudes and in the eastern areas of the vast ocean basins. Thanks to wind-driven currents and large-scale patterns of circulation, the heat is generally driven westward and toward the poles, being lost as it escapes to the atmosphere and space.
This heat loss comes mainly from a combination of evaporation and reradiation into space. This oceanic heat movement helps make Earth habitable by smoothing out local and seasonal temperature extremes. But the transport of heat in the oceans and its eventual loss upward are affected by many factors, such as the ability of the currents and wind to mix and churn, driving heat down into the ocean. The upshot is that no model of climate change can be accurate unless it accounts for these complicating processes in a detailed way. And that’s a fiendish challenge, not least because Earth’s five great oceans occupy 140 million square miles, or 71 percent of the planet’s surface.
“We can see the clear impact of the greenhouse-gas effect in the ocean. When we measure from the surface all the way down, and we measure globally, it’s very clear.”
Providing such detail is the purpose of the Argo program, run by an international consortium involving 30 nations. The group operates a global fleet of some 4,000 undersea robotic craft scattered throughout the world’s oceans. The vessels are called “floats,” though they spend nearly all of their time underwater, diving thousands of meters while making measurements of temperature and salinity. Drifting with ocean currents, the floats surface every 10 days or so to transmit their information to data centers in Brest, France, and Monterey, Calif. The data is then made available to researchers and weather forecasters all over the world.
The Argo system, which produces more than 100,000 salinity and temperature profiles per year, is a huge improvement over traditional methods, which depended on measurements made from ships or with buoys. The remarkable technology of these floats and the systems technology that was created to operate them as a network was recognized this past May with the IEEE Corporate Innovation Award, at the 2022 Vision, Innovation, and Challenges Summit. Now, as Argo unveils an ambitious proposal to increase the number of floats to 4,700 and increase their capabilities, IEEE Spectrum spoke with Susan Wijffels, senior scientist at the Woods Hole Oceanographic Institution on Cape Cod, Mass., and cochair of the Argo steering committee.
Susan Wijffels on…
The need for a global ocean-monitoring system
How the Argo system works
What the Argo system has discovered about the oceans and their role in climate change
The future of the Argo system
Back to top
Why do we need a vast network like Argo to help us understand how Earth’s climate is changing?
Susan Wijffels: Well, the reason is that the ocean is a key player in Earth’s climate system. So, we know that, for instance, our average climate is really, really dependent on the ocean. But actually, how the climate varies and changes, beyond about a two-to-three-week time scale, is highly controlled by the ocean. And so, in a way, you can think that the future of climate—the future of Earth—is going to be determined partly by what we do, but also by how the ocean responds.
Headshot of a smiling woman with short hair.Susan Wijffels
Aren’t satellites already making these kind of measurements?
Wijffels: The satellite observing system, a wonderful constellation of satellites run by many nations, is very important. But they only measure the very, very top of the ocean. They penetrate a couple of meters at the most. Most are only really seeing what’s happening in the upper few millimeters of the ocean. And yet, the ocean itself is very deep, 5, 6 kilometers deep, around the world. And it’s what’s happening in the deep ocean that is critical, because things are changing in the ocean. It’s getting warmer, but not uniformly warm. There’s a rich structure to that warming, and that all matters for what’s going to happen in the future.
How was this sort of oceanographic data collected historically, before Argo?
Wijffels: Before Argo, the main way we had of getting subsurface information, particularly things like salinity, was to measure it from ships, which you can imagine is quite expensive. These are research vessels that are very expensive to operate, and you need to have teams of scientists aboard. They’re running very sensitive instrumentation. And they would simply prepare a package and lower it down the side into the ocean. And to do a 2,000-meter profile, it would maybe take a couple of hours. To go to the seafloor, it can take 6 hours or so.
The ships really are wonderful. We need them to measure all kinds of things. But to get the global coverage we’re talking about, it’s just prohibitive. In fact, there are not enough research vessels in the world to do this. And so, that’s why we needed to try and exploit robotics to solve this problem.
Back to top
Pick a typical Argo float and tell us something about it, a day in the life of an Argo float or a week in the life. How deep is this float typically, and how often does it transmit data?
Wijffels: They spend 90 percent of their time at 1,000 meters below the surface of the ocean—an environment where it’s dark and it’s cold. A float will drift there for about nine and a half days. Then it will make itself a little bit smaller in volume, which increases its density relative to the seawater around it. That allows it to then sink down to 2,000 meters. Once there, it will halt its downward trajectory, and switch on its sensor package. Once it has collected the intended complement of data, it expands, lowering its density. As the then lighter-than-water automaton floats back up toward the surface, it takes a series of measurements in a single column. And then, once they reach the sea surface, they transmit that profile back to us via a satellite system. And we also get a location for that profile through the global positioning system satellite network. Most Argo floats at sea right now are measuring temperature and salinity at a pretty high accuracy level.
How big is a typical data transmission, and where does it go?
Wijffels: The data is not very big at all. It’s highly compressed. It’s only about 20 or 30 kilobytes, and it goes through the Iridium network now for most of the float array. That data then comes ashore from the satellite system to your national data centers. It gets encoded and checked, and then it gets sent out immediately. It gets logged onto the Internet at a global data assembly center, but it also gets sent immediately to all the operational forecasting centers in the world. So the data is shared freely, within 24 hours, with everyone that wants to get hold of it.
An animated gift of the globe with colored dots to represent the floats.This visualization shows some 3,800 of Argo’s floats scattered across the globe.ARGO PROGRAM
You have 4,000 of these floats now spread throughout the world. Is that enough to do what your scientists need to do?
Wijffels: Currently, the 4,000 we have is a legacy of our first design of Argo, which was conceived in 1998. And at that time, our floats couldn’t operate in the sea-ice zones and couldn’t operate very well in enclosed seas. And so, originally, we designed the global array to be 3,000 floats; that was to kind of track what I think of as the slow background changes. These are changes happening across 1,000 kilometers in around three months—sort of the slow manifold of what’s happening to subsurface ocean temperature and salinity.
So, that’s what that design is for. But now, we have successfully piloted floats in the polar oceans and the seasonal sea-ice zones. So we know we can operate them there. And we also know now that there are some special areas like the equatorial oceans where we might need higher densities [of floats]. And so, we have a new design. And for that new design, we need to get about 4,700 operating floats into the water.
But we’re just starting now to really go to governments and ask them to provide the funds to expand the fleet. And part of the new design calls for floats to go deeper. Most of our floats in operation right now go only as deep as about 2,000 meters. But we now can build floats that can withstand the oceans’ rigors down to depths of 6,000 meters. And so, we want to build and sustain an array of about 1,200 deep-profiling floats, with an additional 1,000 of the newly built units capable of tracking the oceans by geochemistry. But this is new. These are big, new missions for the Argo infrastructure that we’re just starting to try and build up. We’ve done a lot of the piloting work; we’ve done a lot of the preparation. But now, we need to find sustained funding to implement that.
Equipment is seen inside a sphere which sits on a table.A new generation of deep-diving Argo floats can reach a depth of 6,000 meters. A spherical glass housing protects the electronics inside from the enormous pressure at that depth.MRV SYSTEMS/ARGO PROGRAM
What is the cost of a typical float?
Wijffels: A typical cold float, which just measures temperature, salinity, and operates to 2,000 meters, depending on the country, costs between $20,000 and $30,000 U.S. dollars. But they each last five to seven years. And so, the cost per profile that we get, which is what really matters for us, is very low—particularly compared with other methods [of acquiring the same data].
Back to top
What kind of insights can we get from tracking heat and salinity and how they’re changing across Earth’s oceans?
Wijffels: There are so many things I could talk about, so many amazing discoveries that have come from the Argo data stream. There’s more than a paper a day that comes out using Argo. And that’s probably a conservative view. But I mean, one of the most important things we need to measure is how the ocean is warming. So, as the Earth system warms, most of that extra heat is actually being trapped in the ocean. Now, it’s a good thing that that heat is taken up and sequestered by the ocean, because it makes the rate of surface temperature change slower. But as it takes up that heat, the ocean expands. So, that’s actually driving sea-level rise. The ocean is pumping heat into the polar regions, which is causing both sea-ice and ice-sheet melt. And we know it’s starting to change regional weather patterns as well. With all that in mind, tracking where that heat is, and how the ocean circulation is moving it around, is really, really important for understanding both what’s happening now to our climate system and what’s going to happen to it in the future.
What has Argo’s data told us about how ocean temperatures have changed over the past 20 years? Are there certain oceans getting warmer? Are there certain parts of oceans getting warmer and others getting colder?
Wijffels: The signal in the deep ocean is very small. It’s a fraction, a hundredth of a degree, really. But we have very high precision instruments on Argo. The warming signal came out very quickly in the Argo data sets when averaged across the global ocean. If you measure in a specific place, say a time series at a site, there’s a lot of noise there because the ocean circulation is turbulent, and it can move heat around from place to place. So, any given year, the ocean can be warm, and then it can be cool…that’s just a kind of a lateral shifting of the signal.
“We have discovered through Argo new current systems that we knew nothing about….There’s just been a revolution in our ability to make discoveries and understand how the ocean works.”
But when you measure globally and monitor the global average over time, the warming signal becomes very, very apparent. And so, as we’ve seen from past data—and Argo reinforces this—the oceans are warming faster at the surface than at their depths. And that’s because the ocean takes a while to draw the heat down. We see the Southern Hemisphere warming faster than the Northern Hemisphere. And there’s a lot of work that’s going on around that. The discrepancy is partly due to things like aerosol pollution in the Northern Hemisphere’s atmosphere, which actually has a cooling effect on our climate.
But some of it has to do with how the winds are changing. Which brings me to another really amazing thing about Argo: We’ve had a lot of discussion in our community about hiatuses or slowdowns of global warming. And that’s because of the surface temperature, which is the metric that a lot of people use. The oceans have a big effect on the global average surface temperature estimates because the oceans comprise the majority of Earth’s surface area. And we see that the surface temperature can peak when there’s a big El Niño–Southern Oscillation event. That’s because, in the Pacific, a whole bunch of heat from the subsurface [about 200 or 300 meters below the surface] suddenly becomes exposed to the surface. [ Editor’s note: The El Niño–Southern Oscillation is a recurring, large-scale variation in sea-surface temperatures and wind patterns over the tropical eastern Pacific Ocean.]
What we see is this kind of chaotic natural phenomena, such as the El Niño–Southern Oscillation. It just transfers heat vertically in the ocean. And if you measure vertically through the El Niño or the tropical Pacific, that all cancels out. And so, the actual change in the amount of heat in the ocean doesn’t see those hiatuses that appear in surface measurements. It’s just a staircase. And we can see the clear impact of the greenhouse-gas effect in the ocean. When we measure from the surface all the way down, and we measure globally, it’s very clear.
Argo was obviously designed and established for research into climate change, but so many large scientific instruments turn out to be useful for scientific questions other than the ones they were designed for. Is that the case with Argo?
Wijffels: Absolutely. Climate change is just one of the questions Argo was designed to address. It’s really being used now to study nearly all aspects of the ocean, from ocean mixing to just mapping out what the deep circulation, the currents in the deep ocean, look like. We now have very detailed maps of the surface of the ocean from the satellites we talked about, but understanding what the currents are in the deep ocean is actually very, very difficult. This is particularly true of the slow currents, not the turbulence, which is everywhere in the ocean like it is in the atmosphere. But now, we can do that using Argo because Argo gives us a map of the sort of pressure field. And from the pressure field, we can infer the currents. We have discovered through Argo new current systems that we knew nothing about. People are using this knowledge to study the ocean eddy field and how it moves heat around the ocean.
People have also made lots of discoveries about salinity; how salinity affects ocean currents and how it is reflecting what’s happening in our atmosphere. There’s just been a revolution in our ability to make discoveries and understand how the ocean works.
A diagram showing the cycle an undersea profiling float moves through while gathering and transmitting data.During a typical 10-day cycle, an Argo float spends most of its time at a depth of 2,000 meters, making readings before ascending to the surface and then transmitting its data via a satellite network.ARGO PROGRAM
As you pointed out earlier, the signal from the deep ocean is very subtle, and it’s a very small signal. So, naturally, that would prompt an engineer to ask, “How accurate are these measurements, and how do you know that they’re that accurate?”
Wijffels: So, at the inception of the program, we put a lot of resources into a really good data-management and quality-assurance system. That’s the Argo Data Management system, which broke new ground for oceanography. And so, part of that innovation is that we have, in every nation that deploys floats, expert teams that look at the data. When the data is about a year old, they look at that data, and they assess it in the context of nearby ship data, which is usually the gold standard in terms of accuracy. And so, when a float is deployed, we know the sensors are routinely calibrated. And so, if we compare a freshly calibrated float’s profile with an old one that might be six or seven years old, we can make important comparisons. What’s more, some of the satellites that Argo is designed to work with also give us ability to check whether the float sensors are working properly.
And through the history of Argo, we have had issues. But we’ve tackled them head on. We have had issues that originated in the factories producing the sensors. Sometimes, we’ve halted deployments for years while we waited for a particular problem to be fixed. Furthermore, we try and be as vigilant as we can and use whatever information we have around every float record to ensure that it makes sense. We want to make sure that there’s not a big bias, and that our measurements are accurate.
Back to top
You mentioned earlier there’s a new generation of floats capable of diving to an astounding 6,000 meters. I imagine that as new technology becomes available, your scientists and engineers are looking at this and incorporating it. Tell us how advances in technology are improving your program.
Wijffels: [There are] three big, new things that we want to do with Argo and that we’ve proven we can do now through regional pilots. The first one, as you mentioned, is to go deep. And so that meant reengineering the float itself so that it could withstand and operate under really high pressure. And there are two strategies to that. One is to stay with an aluminum hull but make it thicker. Floats with that design can go to about 4,000 meters. The other strategy was to move to a glass housing. So the float goes from a metal cylinder to a glass sphere. And glass spheres have been used in ocean science for a long time because they’re extremely pressure resistant. So, glass floats can go to those really deep depths, right to the seafloor of most of the global ocean.
The game changer is a set of sensors that are sensitive and accurate enough to measure the tiny climate-change signals that we’re looking for in the deep ocean. And so that requires an extra level of care in building those sensors and a higher level of calibration. And so we’re working with sensor manufacturers to develop and prove calibration methods with tighter tolerances and ways of building these sensors with greater reliability. And as we prove that out, we go to sea on research vessels, we take the same sensors that were in our shipboard systems, and compare them with the ones that we’re deploying on the profiling floats. So, we have to go through a whole development cycle to prove that these work before we certify them for global implementation.
You mentioned batteries. Are batteries what is ultimately the limit on lifetime? I mean, I imagine you can’t recharge a battery that’s 2,000 meters down.
Wijffels: You’re absolutely right. Batteries are one of the key limitations for floats right now as regards their lifetime, and what they’re capable of. If there were a leap in battery technology, we could do a lot more with the floats. We could maybe collect data profiles faster. We could add many more extra sensors.
So, battery power and energy management Is a big, important aspect of what we do. And in fact, the way that we task the floats, it’s been a problem with particularly lithium batteries because the floats spend about 90 percent of their time sitting in the cold and not doing very much. During their drift phase, we sometimes turn them on to take some measurements. But still, they don’t do very much. They don’t use their buoyancy engines. This is the engine that changes the volume of the float.
And what we’ve learned is that these batteries can passivate. And so, we might think we’ve loaded a certain number of watts onto the float, but we never achieved the rated power level because of this passivation problem. But we’ve found different kinds of batteries that really sidestep that passivation problem. So, yes, batteries have been one thing that we’ve had to figure out so that energy is not a limiting factor in float operation.